The experienced detectorists at Minelab have put together a comprehensive list of FAQs on how to use a metal detector. These also contain many pro tips for metal detecting.
You may find the answers to your questions by reading the FAQs here and from the related Knowledge Base Articles. Of course, if, after searching through this information you still have a question, there please contact our customer service team.
Yes, Minelab metal detectors have the ability to ‘discriminate’ between different types of targets. The discrimination feature on Minelab detectors measure two target properties, ferrous properties and conductive properties.
Ferrous properties refer to how much iron is in a target and therefore how strongly it’s attracted to a magnet. Ferrous targets tend to be trash, so can be discriminated/masked out based on their ferrous properties alone by the detector. Conductive properties refer to how well a target conducts electrical current and therefore responds to a metal detector’s magnetic field. Trash like nails and foil have different conductive properties to valuable targets like coins and rings. In this case the metal detector can make a judgement as to whether the target is trash based on conductivity.
The process for configuring the discrimination settings and the method used to indicate treasure or trash varies across the Minelab range of detectors.
As a rule of thumb, the lower the frequency used by the detector, the deeper it can penetrate the ground. At low frequencies however, sensitivity to small low conductive targets is reduced. The higher the frequency, the higher the sensitivity to small targets, but will not penetrate as deeply. In general, gold detectors operate at higher frequencies (to find small nuggets), while coin and treasure detectors work at lower frequencies for deeper penetration. The exception to this is MPS type metal detectors that are sensitive and deep seeking simultaneously.
Size
The size of a search coil can influence the detection depth or sensitivity of a metal detector. The larger the coil, the deeper it detects, but will have less sensitivity to small targets. Conversely the smaller the search coil’s diameter, the more sensitive it becomes but looses detection depth.
Smaller coils are lighter, easier to control and may be chosen for their ability to negotiate difficult terrain or undergrowth. They are also an advantage in areas of high trash.
Shape
The most common coil shapes are conventional solid round coils, elliptical shaped coils and the open web coils. The main reason for the change in shape is to conform to a physical requirement, i.e. an elliptical coil can be pushed around bushes or between rocks easier than a round coil and open web coils move through water easier and are lighter. Conventional round coils are often more stable and perform better and are particularly popular for gold prospecting.
Configuration
The three most common types of coil windings are Concentric, Double-D, and Monoloop. The difference between these coil types is the pattern the wire is wound within the search coil.
Concentric coil
A Concentric coil has an inner circle and an outer circle wire winding. Its search pattern is cone shaped and can be useful for accurately pinpointing a target. Concentric coils tend to be noisier in highly mineralised ground and require more over lap of sweep for thorough ground coverage.
Double-D coil
Double-D coils are the preferred coils for most detecting. They give a blade or chisel shaped signal that covers the ground more uniformly and once an operator becomes accustomed to the signal, pinpointing can be very accurate. Double-D coils are also preferred for their superior ground balancing ability.
Monoloop coil
Monoloop coils have one winding of wire around the circumference of the coil, which is used to both transmit and receive. The signal pattern of the Monoloop coil is cone shaped, requiring more overlapping. In extremely heavily mineralised grounds they can be more difficult to ground balance, however they tend to provide slightly better depth than the Double-D coils.
Dirt, dust and moisture can be trapped inside the skidplate leading to false signals and poor performance. To maintain peak performance of your Minelab detector, it is recommended to clean out the skidplate quite regularly.
Algılama ihtiyaçlarınız için en uygun bobini bulmak için bobin seçim kılavuzunu kontrol edin.
Headphone specifications are not really critical in a metal detector as their audio circuitry does not produce Hi-Fi quality sound. e.g. Our detectors frequency output range is only circa 75 -1200Hz
Our audio circuits will drive most headphones from 16 - 100 + ohms.
Audio optimisation is also very subjective as everybody hears differently.
We endeavour not to confuse our customers with unnecessary technical specs because in reality there is no honest way to determine what headphones are best for you other than to try them.
If you have a detector with adjustable audio tones, such as a CTX 3030, we would also recommend you spend some time to ensure the detection tones are optimised for your hearing needs.
There is no specific answer to this question as it depends on the target size, orientation, metallic content, ground minerals and conductivity, electrical and ambient noise in the area and etc.
However we commonly hear of GPX Series detectors finding large gold nuggets at 3 and sometimes 4 feet deep, and CTX 3030s finding coins and rings at over 12 inches.
Only if it becomes faulty.
On some detectors you don’t need to ground balance at all. On others, users new to detecting are recommended to use the Ground Balance Tracking function.
In Tracking, the detector will automatically ground balance for you and remain in balance even if the ground minerals vary. On manual ground balance detectors like the X-TERRA 305 and X-TERRA 505, you need to ground balance at the start of every hunt, and re-balance periodically as required. Always ground balance on clean ground, away from metal objects.
Gold chains are very difficult to detect, particularly very fine chains. Each link of a chain can be very small and the detector sees each link as a separate target, so it can easily be missed. You are more likely to detect the actual clasp or any pendants that may still be on the chain as these are much larger than the individual chain links. High frequency detectors such as the Eureka Gold, or an X-TERRA 705 with an 18.75 kHz coil in prospecting mode, will often pick up fine chains better than most coin detectors.
Coke is carbon and as such can be quite conductive, just like a coin.
The GPZ 7000 is our deepest detector in all ground conditions and can detect through even highly mineralised rock.
No, cable characteristics are matched to coil windings at manufacture, so extending the cable will reduce the performance of the coil.
Smaller coils are better for trashy sites, as they reduce the instances of detecting multiple targets at once. Concentric coils are generally better than Double-D coils for this same reason.
Check the coil selection guide to find the most suitable coil for your detecting needs.
Metal detectors pick up electromagnetic signals from underground metal objects. Similar signals can also be received through the air from other electromagnetic sources, such as power lines, radio transmitters, generators, etc.
If your detector is noisy when you are detecting, but goes quiet when you stop sweeping the coil, then it is receiving signals from mineralized ground. Perform a ground balance and continue detecting.
GPX series only: if it is still noisy then you may need to try an alternate soil/timing selection. All other detectors: if it is still noisy you would need to reduce your sensitivity to the highest stable sensitivity level.
The only guaranteed way to get every possible good target is to use no discrimination. However, digging every target can waste lots of time. Discrimination patterns are always a compromise between digging most good targets and ignoring most junk targets.
This can be caused by a number of reasons:
Usually because you are lifting the coil at the end of your swing. Always sweep slow, low and level for the entire swing.
Zero Voltage Transmission (ZVT) technology creates ultra‑constant high-power opposite polarity magnetic fields.
ZVT provides users with superior ground balance to enhance detector stability in mineralised soils and will detect gold nuggets at extreme depths that exceed all current competitor products.
The GPZ 7000 is our best performer on the medium to larger nuggets, even in highly mineralised or variable ground. It retains superior depth capabilities compared to any other detector while still providing good sensitivity to smaller, shallower targets.
The GPZ 7000 detector has Minelab branded, and aftermarket coils available for purchase. Minelab branded coils are available from Minelab certified dealerships. You can purchase the 14” or 19” Super-D coils.
NuggetFinder coil have released 2 Minelab approved aftermarket coils. A 12” round Super-D coil and a 17” elliptical Super-D coil which can be purchased by NuggetFinder stockists.
No, the GPZ 7000 does not have any discrimination capability.
The Difficult Ground Type setting is the default setting and is recommended as gold is usually found in areas with highly mineralised soils.
The Normal Ground Type setting will provide the greatest detection depth but can only be used in “quiet” soils where there are lower levels of mineralisation in the soil.
If the detector is running unstable or noisy when using a “Normal” ground type you should switch to “Difficult”.
The Severe Ground Type will provide the lowest detection depth and should only be used when detecting in areas with extremely high levels of mineralisation. This setting should only be used in areas where you need to raise the coil above the ground when using the “Difficult” Ground Type setting.
When ground balancing, the yellow ferrite ring artificially adds additional data to help the GPZ 7000 improve the ground balance accuracy. This should always be used to ensure smooth operation. Sweep the coil over the yellow ferrite ring in a figure 8 motion ground balancing, ensuring that you sweep over the yellow ferrite ring with each figure 8 movement.
When balanced correctly you should hear a smooth audio tone when sweeping the coil over the yellow ferrite ring.
When ground balancing the GPZ 7000 a swinging or figure-8 movement is recommended as the GPZ 7000 constantly monitors the changes in the soil. Sweeping the coil over as much ground as possible ensuring that you sweep over the yellow ferrite ring with each swing/figure-8 motion when ground balancing allows the detector to gain as much information as possible about the local ground conditions which provides a superior ground balance.
Wireless audio is susceptible to audio dropouts when the signal is blocked. Audio dropouts can be reduced by ensuring a direct line of sight between the WM12 and the detector. It is best to wear the WM12 as close as possible to the detector. This minimises the path to the wireless transmitter and makes it less likely that the operator's body will block the signal path between the WM12 and the detector.
The GPZ 7000 will operate for approximately 8 hours when commencing with a fully charged battery. Charging the battery will typically take 5 – 6 hours.
The WM12 wireless module will operate for approximately 12 hours on a fully charged battery and takes around 12 hours to charge when charging via the BC10 charger.
Yes, the GPZ 7000 can be charged from a nominal 24V battery system. The BC10 charger can will function between 11 – 30 volts DC.
You can also use the supplied 240V AC plug-pack if your vehicle is fitted with an inverter.
No, Minelab currently has no plans to release a replaceable cell or alkaline battery pack.
There are 2 USB cables supplied in the box with your GPZ 7000. The USB-A to Mini-USB cable is used for charging the WM12 wireless module.
The USB-A to USB-B is used for software updates and is plugged into the rear of the screen pod and a PC.
On the rear of the screen pod is a USB-B port that can be used if a software upgrade is released. Check the downloads section of the GPZ 7000 page on our website for updates.
GeoSense-PI™ teknolojisi, zemin sinyallerini büyük netlik ve hassasiyetle analiz eder ve bunlara yanıt verir, böylece bir zamanlar algılanamaz olduğu düşünülen zorlu ortamlarda algılama yapabilirsiniz. En küçük altın parçalarının bile süper hızlı tespiti için üst üste binen üç geri bildirim sistemi aracılığıyla istenmeyen sinyalleri hızla bastırır.
GPX 6000, çok mineralli veya değişken zeminlerde bile, daha bol olan küçük külçeler üzerinde en iyi performans gösterenimizdir. Daha büyük, daha derin külçelerde GPZ 7000'in hemen arkasında mükemmel derinliği korur.
GPX 6000 bobinleri, önceki GPX serisi dedektörlerle uyumlu olmayan yeni bir hafif, yüksek performanslı bobin serisidir.
GPX 6000'deki 14" Double-D bobini, yalnızca iletken toprak sinyallerinin EMI iptali veya iptali için kullanılabilir. Demirli ayrım yapamaz.
The following Minelab coils are currently available to operate with the GPX 6000:
Minelab approved aftermarket coils are available from Coiltek and NuggetFinder.
Bobin kablosunun bobinden ilk sarımı her zaman şaftın üzerinden geçmelidir. Bobin kablosu daha sonra şaftın etrafına sıkıca sarılmalı ve iki cırt bantla yerinde tutulmalıdır. Tespit sırasında bobinin serbestçe hareket edebilmesi için yeterli alana izin vermelisiniz.
GPX 6000, zeminin Ferrit bileşenini izlemez. GeoSense-PI, operatör tarafından görülmeyen 'X' yanıtını kaldırmak için başka teknikler kullanır.
GPX 6000'in toprak dengesini sağlamak için sarı bir ferrite ihtiyacınız yoktur.
Zemin Tipi düğmesine uzun basılarak eşik tonu herhangi bir hassasiyet ayarında açılıp kapatılabilir.
Eşik tonunun Manuel hassasiyet aralıklarında açık olduğunu ve Otomatik hassasiyet aralıklarında kapalı olduğunu unutmayın. GPX 6000'in bir sonraki açılışında, Eşik tonu varsayılanına dönecektir.
Zor Zemin Tipi ayarı, özellikle sıcak kayalar veya oldukça değişken zeminler olmak üzere, daha yoğun mineralli topraklarda en iyi şekilde kullanılır.
Normal Zemin Türü ayarı, daha büyük külçelerde en büyük derinliğe sahiptir; mümkün olan her yerde ve her zaman daha düşük mineralizasyon seviyelerine veya daha az değişken zemine sahip zeminlerde en iyi şekilde kullanılır. Normal zemin tipi, hedef olarak sıcak kayaları alabilir. Sıcak kayaların zemin dengesi yapılamıyorsa, Zor zemin tipi ayarını kullanmanız gerekecektir.
The GPX 6000 with GeoSense-PI is continually tracking the ground, so either technique would work. Minelab recommends pumping the GPX 6000 up and down above the ground with the Quick-Trak button depressed to achieve the fastest Ground Balance.
İletken zeminin görünür tuzla ilişkilendirilmesi gerekmez. Örneğin, son yağmurlar toprağı daha iletken hale getirebilir ve istenmeyen iletken toprak tepkisini artırabilir.
Kablosuz ses, sinyal engellendiğinde ses kesintilerine karşı hassastır. Kulaklıklar ve dedektör arasında doğrudan bir görüş hattı sağlanarak ses kesintileri azaltılabilir. Bluetooth kontrolleri dedektöre en yakın olan kulaklıkları takmak en iyisidir. Bu, Bluetooth vericisine giden yolu en aza indirir ve operatörün vücudunun kulaklıklar ile dedektör arasındaki sinyal yolunu engelleme olasılığını azaltır.
GPX 6000, tam şarjlı bir pille başlatıldığında yaklaşık 8 saat çalışacaktır. Pilin şarj edilmesi genellikle 5 – 6 saat sürer.
ML 100 kulaklık, tam şarjlı bir pille yaklaşık 24 saat çalışır ve şarj olması yaklaşık 3,5 saat sürer.
GPX 6000 aküsü, bir araçtan şarj edilirken yalnızca nominal bir 12V araç aküsü sisteminden şarj edilmelidir.
Minelab'ın şu anda değiştirilebilir bir pil veya alkalin pil paketi çıkarma planı yoktur.
USB kablosu Bluetooth kulaklıkları şarj etmek için kullanılır ve GPX 6000 için bir yazılım yükseltmesi mevcutsa kullanılır.
Hoparlör ızgarasının arkasında, bir yazılım yükseltmesi yayınlandığında kullanılabilecek bir USB bağlantı noktası bulunur. Güncellemeler için web sitemizdeki GPX 6000 sayfasının indirmeler bölümünü kontrol edin.
Herhangi bir yerde hangi seviyede toprak mineralizasyonunun olacağını asla tahmin edemezsiniz, bu nedenle başlamak için önerilen Zamanlama Normal'dir. Ardından, bobini süpürerek ve eşiğin kararlılığını dinleyerek dedektörün hangi Zamanlamanın kullanılacağını size söylemesine izin verebilirsiniz.
Otomatik Ayar ve Zemin Dengesi yaptıktan sonra aramaya başlamalısınız ve dedektör çok gürültülüyse veya çok sayıda sıcak kayada sinyal veriyorsa, kullandığınız Zamanlama üzerinde bulunduğunuz zemin için çok agresiftir. Aşağıdaki ölçeğin karanlık ucuna daha yakın başka bir Zamanlama seçmeniz gerekir, örneğin Geliştirme.
GPX 5000'in özellikle fırtınalı havalarda Elektromanyetik Girişimden (EMI) muzdarip olduğu bilinmektedir. Bu müdahalenin bilinen üç nedeni vardır:
Kötü EMI günlerinde, eşiğinizin mırıldanmasını sağlayabilecek birkaç ipucu:
Bobin Rx anahtarı İptal olarak ayarlanmış bir Monoloop bobini kullanmadığınızdan emin olun.
Monoloop bobinler mükemmel yuvarlak bir kabloya sahiptir.
Çift D bobinleri, iki dahili çekirdek nedeniyle daha düz bir kabloya sahiptir.
Bobin/Rx anahtarını İptal'e getirin. Beklediğinizden biraz daha düşük derinliğiniz varsa, o zaman bobininiz bir Double-D'dir. Neredeyse hiç derinliğiniz yoksa, Monoloop bobininiz var demektir.
Sabitleyici işlevi, Eşikteki zayıf değişikliklerin duyulmaya başladığı noktayı kontrol eder. Bu zayıf varyasyonlar, ortam gürültüsü veya zayıf hedef sinyalleri olabilir. Sabitleyici kontrolünü artırdıkça, zayıf hedef sinyalleri daha yüksek olacaktır, ancak gürültü seviyesi de artacak ve bu da potansiyel olarak istenen bir hedef sinyalini gizleyebilecektir. Stabilizatör, mükemmel kararlı bir eşik sağlamak için bu zayıf varyasyonları maskelemenize izin vererek zayıf hedef sinyallerini belirleme yeteneğinizi geliştirir.
Stabilizatör, konumdaki toprak koşulları belirlenene kadar en iyi şekilde FP (fabrika ön ayarı) konumunda bırakılır. Yerel koşullar için Rx Kazanç seviyesi ayarlandıktan ve diğer ses ayarları seçildikten sonra, Eşik kararlılığının ince ayarını yapmak için Sabitleyici kullanılabilir.
Sabitleyicinin en uygun konumunu bulmak için bobinin zeminde süpürüldüğünden emin olun. Eşiğin titremeye başladığı noktanın altındaki bir sayı genellikle en iyi ayardır.
Sabitleyicinin etkisinin, Rx Kazanç kontrolününkine benzer bir etkiye sahip olduğu görülebilir. Ancak, Sabitleyici yalnızca ses işlemeyi etkiler ve Alma (Rx) sinyalini değiştirmez, bu nedenle son aşama ince ayarı olarak kullanılmalıdır. Stabilizatörde herhangi bir ayar yaptıktan sonra, zemin koşulları değişirse veya bobinleri değiştirmek isterseniz, Rx Gain'i sıfırlamanız gerekebilir, ancak bunu yapmadan önce Stabilizörü Fabrika Ayarlarına geri döndürün. Bu, koşullara en uygun Rx Kazanç seviyesini seçmenizi sağlar ve ardından Stabilizörü kullanarak ince ayar yapabilirsiniz.
İpucu: Sabitleyici kontrolünü minimuma (saat yönünün tersine) yaklaştırarak, eşik çok kararlı olacaktır, ancak daha küçük hedeflere karşı çok fazla hassasiyet kaybetmiş olacaksınız. Bu, yüksek miktarda çöp bulunan bir alanda büyük külçeler aramak veya madeni para veya hazine aramak için GPX 5000 ve GPX 4800'ü kullanmak gibi belirli senaryolarda istenen bir özellik olabilir.
İpucu: Bu kontrolleri ayarlamak için en iyi sırayı öneriyoruz:
Hedef Hacim, hedef sinyallerin gücünü kontrol eder ve 8'in üzerindeki ayarlarda eşiğin sesini de biraz artıracaktır. Bu, çok rüzgarlı koşullarda, işitme kaybı olan kişiler için veya harici hoparlörler kullanırken kullanışlıdır. Li-Ion pil takımına yerleşik ses yükseltici ile, doğrudan pile bir hoparlör takabilir ve Hedef Hacmi kullanarak uygun bir amplifikasyon seviyesi ayarlayabilirsiniz. Kulaklıktan harici bir hoparlöre geçerken, Eşik ve Ses Sınırı kontrollerinizde küçük ayarlamalar yapmanız gerekebileceğini unutmayın.
Hedef Hacim, sessiz koşullarda bir Ses takviyesi olarak kullanılabilir ve ayrıca yüksek oranda mineralli topraklarda zemin gürültü sinyallerini azaltmak veya yumuşatmak için kullanılabilir. Bu güçlü bir özelliktir ve Stabilizer kontrolü ile birlikte çalışarak size en üst düzeyde ince ayar yeteneği sağlar. Farklı koşullarda optimum kombinasyonu bulmak için biraz deneme yapmak gerekebilir.
NOT: Bobin veya yer değişikliği nedeniyle Kazançta ayarlama yapılması gerektiğinde, önce Hedef Hacmin FP ayarına döndürüldüğünden emin olun. Daha sonra yeni koşullara uyacak şekilde ince ayar yapabilirsiniz.
The SDC 2300 is our compact and waterproof gold prospecting detector. It uses Multi Period Fast (MPF) Pulse Induction (PI) technology that provides excellent sensitivity when detecting small to medium sized nuggets in highly mineralised or variable ground. The SDC 2300 provides good depth on larger deeper nuggets.
No, there are no other Minelab branded coils available for the SDC 2300. The supplied 8” round coil provides excellent overall performance for the SDC 2300 and keeps the detector waterproof and compact
No, there is no discrimination function available for the SDC 2300.
Having no constant threshold audio emit through the speaker or headphones indicates that the threshold audio is in the OFF or minimum setting.
The threshold volume can be adjusted by pushing the threshold button on the right side of the handle.
There are 9 levels of Threshold audio which are indicated by the LED display. With each press of the threshold button, you will notice the LEDs on the display incrementally move to the right, the threshold audio will also start increasing. When the threshold level is at maximum, pressing the Threshold button will cycle the threshold level back to the OFF or minimum setting.
The SDC 2300 has 2 Audio pitch settings, Low or High. High pitch is the default, to change to the low setting switch the detector off then push and hold the Threshold button while switching the detector on.
The SDC 2300 will remember its previous setting so you will need to push and hold the Threshold button whilst switching the detector on to toggle back to the High pitch setting.
The SDC 2300 is waterproof to 3m (10ft) This is the complete detector including the control box.
Yes, the SDC 2300 has a salt mode in the sensitivity adjustment, however Minelab does not recommend using the SDC 2300 on the beach as the SDC 2300 does not have a discrimination or target ID feature so you will dig a lot of trash.
The salt mode in your SDC 2300 is designed to be used on conductive ground such as salt lakes or wet mineralised soils found in gold fields where a high salt content is apparent. For example, recent rains may make the soil more conductive and increase the unwanted conductive soil response. If the soil is conductive or you are detecting on a salt lake, then adjust the sensitivity dial to a salt setting.
To check the battery level on your SDC 2300 simply push and hold the Noise Cancel button then press and release the Threshold button. The Noise Cancel button can now be released.
An indication of the battery level will be displayed by the LED's for approximately 3 seconds.
The SDC 2300 will operate for approximately 8 hours when commencing with a fully charged Li-Ion battery. Charging the battery will typically take 5 – 6 hours. When using C-Cell Alkaline batteries you will generally have a longer use time (10-14 hours) but this will depend on the quality of the C-Cell batteries you are using.
No, The SDC 2300 battery should only be charged from a nominal 12V car battery system when charging from a vehicle.
The SDC 2300 includes a rechargeable Li-Ion battery pack inside the box. The battery compartment can also accept C-Cell Alkaline batteries or C-Cell NiMH rechargeable batteries. You can see the polarity for the C-Cell batteries on the side of the control box.
No, the software on the SDC 2300 cannot be upgraded.
The GOLD MONSTER 1000 is Minelab’s entry level gold prospecting detector, designed to find the smallest of nuggets in moderately mineralised ground. It retains excellent sensitivity to smaller shallow nuggets and can detect some larger nuggets at depth.
The Gold Chance Indicator at the top of the screen indicates if the target has a ferrous or non-ferrous content. If the indicator is consistently pointing to the right, it is indicating a high non-ferrous content and is likely a non-ferrous metal such as: gold, silver, brass, copper, aluminium, lead, zinc or other alloys that do not have any iron (ferrous) content.
If the indicator is pointing to the left, it is showing a high ferrous content and is likely steel or iron.
Large steel and iron (ferrous) targets can indicate on the right. This happens when the conductive properties of the large ferrous target dominate the signal and mask the magnetic properties of the target.
The GM05 and GM10 are the only compatible coils that can be used with the GOLD MONSTER 1000. The GM05 is included in the box and the GM10 coil can be purchased as an accessory from Minelab dealerships.
There are currently no aftermarket coils available for the GOLD MONSTER 1000.
The first winding of the coil cable from the coil should always go over the shaft. Winding the coil cable over the shaft provides minimal stress on the coil cable which will help avoid damage. The coil cable should then be wound closely around the shaft, allowing enough room for the coil to be able to move freely when detecting.
Press the coil cable into the clip on the rear of the screen pod and then carefully screw the coil connector into the rear of the screen pod.
There are 10 manual and 2 auto sensitivity levels.
Auto is located in position 11 on the sensitivity dial and will be indicated with a black dot in the centre of the sensitivity dial.
When in Auto the detector will function smoothly in most soil types and will continually adjust the detector’s sensitivity level to maintain smooth operation.
Auto + is located in position 12 on the sensitivity dial and will be indicated with a black dot in the centre of the sensitivity dial.
Auto + is a more aggressive sensitivity which provides users with additional sensitivity for extra depth performance. Auto+ should only be used in moderately mineralised soils as this setting may provide more ground noise.
Manual sensitivity adjustments (1 – 10) are for the expert user who has a good understanding of soil mineralisation and electro-magnetic interference (EMI).
Manual sensitivity allows the user to adjust the detector’s performance manually, when you have selected a sensitivity setting in the manual range the detector will not adjust levels like it does in the Auto or Auto+ modes. You may need to keep adjusting the manual sensitivity when in variable or heavily mineralised soil types.
The GOLD MONSTER 1000 is very sensitive, when you wave your hand over the coil the detector can detect the salt in your blood.
When you are retrieving a target, you should always use the supplied plastic scoop to ensure you detect the desired target and not your hand.
Because the GOLD MONSTER 1000 is highly sensitive to salt detection it is not recommended for beach use.
Chattering, or inconsistent audio is generally a sign that the detector is picking up interference from ground mineralisation or electro-magnetic interference (EMI). If you are in Auto +, try adjusting the sensitivity to Auto or a lower manual sensitivity. If lowering the sensitivity doesn’t fix the issue, then you should move away from sources of EMI. (power lines, cellular phone towers, power generators, thunder/electrical storms, etc.)
Random detection beeps can be caused by mineralisation in the soil. The GOLD MONSTER 1000 has an auto-tracking ground balance feature that continually monitors the minerals in the soil and adjusts the detectors’ ground balance. Rapid changes or high levels of mineralisation in the soil can cause the detector to false signal, if this happens, pump the coil up and down (0.5 - 10cm / 0.2 - 4”) over the areas that are giving false signals. This will help ground balance the detector to the mineralisation in the soil.
If the mineralisation level is too high, then lower the sensitivity to compensate for the mineralisation level.
Lifting your coil into the air will amplify any noise that is in the area. Minelab does not suggest doing this as this is not how our products are designed to be used. Lifting the coil slightly into the air is acceptable when performing a Noise Cancel, once the Noise Cancel is complete the coil should always be kept near the surface of the soil to avoid interference.
No, the GOLD MONSTER 1000 does not have any wireless capability. You can plug in any 3.5mm (1/8”) stereo headphones to the rear of the control pod.
The GOLD MONSTER 1000 will operate for approximately 12 hours when commencing with a fully charged Li-Ion battery. Charging the battery will typically take 5 to 6 hours.
No, the GOLD MONSTER 1000 battery should only be charged from a nominal 12V car battery system when charging from a vehicle.
No, the software in the GOLD MONSTER 1000 cannot be upgraded.
Bazı bilgisayarlardaki virüs koruma yazılımı, Minelab e-postasını bir spam dosyasına / klasörüne yerleştirir, lütfen bu e-posta için spam klasörünüzü kontrol edin. E-postayı almadıysanız, lütfen size en yakın Minelab Yetkili Servis Merkezi ile iletişime geçin.
When XChange 2 is first installed the 'file' icon will not appear until the software recognizes the CTX 3030 being connected for the first time. This is the only time this will happen. After the initial connection the 'FILE' icon will appear and remain. You will no longer need to connect the CTX 3030 to access it.
The factory setting for GeoTrails is off, so you will need to turn it on. First turn GPS ON, then turn GeoTrails ON. From the map screen, press and hold the Map button to access this option. Use the arrows to select ‘View GeoTrails’ and press the Select button.
Enhanced turns on SBAS or Satellite Based Augmentation System which is a generic term for WAAS used in the USA and EGNOS in Europe. These systems use a geostationary satellite to probe the atmosphere and TX this to your GPS receiver. It works well in the USA, but in Europe it seems to be better for planes rather than on the ground. In Australia you get signals from a satellite over Japan which makes your fix worse. Not sure how much of Europe has this as an issue.
The default for the 'User' button is to control the backlight, so if a user changes this to something else, then the backlight is controlled in the Menu/Options/Backlight - ON / OFF / TIME
You’re all done and your time zone has been set.
If you don’t know your UTC Time Zone please refer to the following link: http://www.timeanddate.com/time/map/
In a session, if the WM 10 Wireless Module is enabled and the detector is connected to it then you will hear tones as expected. If you turn off the WM 10 it will 'mute' the detector. Power cycle the detector and you will be able to hear the tones.
The CTX 3030 has a similar ground compensation feature to that on the Explorer SE Pro and E-TRAC models which works very well in most ground conditions, so there is no need to ground balance the CTX 3030 in most conditions. Ground balance should only be performed in 'Extremely Mineralised Ground'. Do not perform ground balance on the beach, this will 'confuse' the detector.
This is a standard feature, when you perform 'Tone ID profile edit', and select Play Tone or Play All, the tones will not sound if the WM 10 Wireless Module is connected.
There are 4 different volume settings. The CTX 3030 remembers what each setting is. If you turn the volume down while using the headphones and then unplug your headphones the external speaker volume will not have changed from your previous setting.
Before placing the twist-lock style armrest on the shaft, turn the lock fully counter clockwise. There is no need to turn the lock completely 90 degrees to lock it. Around 30 to 45 degrees is often sufficient.
This was corrected in a software update. Connect your detector to XChange 2 and check for software updates. We always recommend using the most current software update. If you're on the latest update or the update didn’t correct the problem please contact your regional Minelab Authorised Service Centre.
The modes will change (or be translated) ONLY when changing from ENGLISH to another language and not in reverse. If the detector is initially set up in a language other than English, the modes will appear in that language. But if you change the language to English later, the modes will stay in the original language.
The Trigger will Cancel any adjustment being made and go back one level in the menu.
If you’ve been using the detector a lot since the last time you connected it to XChange 2 then there is a lot of data stored. It could take several minutes for the data to upload. Please be patient.
This could be related to masking, low sensitivity setting, coil overload or etc. Perform a 'Factory Reset' and retest the detector.
To connect the WM 10 Wireless Module to your detector:
If Pairing fails, try selecting another channel
The location of the WM 10 can be an issue for path loss. The human body is very attenuating, so having the WM 10 tucked on your backside away from the detector could cause issues. If you’re having issues place the WM 10 in a clear line of sight to the detector to get best results.
Snapshots are only saved while the detector is on. It is a design feature that the snapshots are deleted when the detector is turned off.
During your initial use of GPS the detector will take a while to build up local data. From a cold start the 'locking in' of where satellites are and etc. takes a few minutes, but it can take an hour to build up lots of local data. This data can be used to get better resolution and shaded sky use.
This is as simple as saving the modes and/or data you want as a file and emailing them the file. Here’s the procedure:
All the modes and other data from your CTX 3030 will be displayed in the list.
The entire FILE Collection will be exported as a single file, and saved in the Downloads folder of your PC. You can then save the file elsewhere or email it to whoever you want.
If you receive a Minelab FILE from someone else simply open XChange 2, select the FILE Collection and then click the ‘Clear the contents of your File collection’ icon.
Then click the ‘Import a Minelab file’ icon.
Then click ‘Choose file’,
and browse for the file location. Highlight the file and click ‘Open’ and the Items within it will be displayed in the File Collection.
Drag and drop the items you want to keep into one of your own Collections or straight into your CTX 3030.
Combined audio produces different tones for highly ferrous objects, and objects with varying levels of conductivity. First you set the ferrous line (horizontal line) where you want ferrous targets to provide the audio response. For example, if you set it at 21, then any target with a ferrous reading of 21 or higher (larger number) will produce the audio tone that you program for ferrous targets. On the other hand, if the target has a ferrous reading that is less than 21, the audio response will be based on its conductive properties. In Combined audio you have four 'bins' representing conductive groups with conductive numbers running from 01 - 50. You simply move the lines to represent different target groups and assign a tone for each group. For example, you could set bin one with the lines at 01 and 14. Any target with a ferrous value less than 21, and a conductive value of 14 or less would fall into this bin and provide the audio tone you associated with it via programming.
Bin two, for example, could represent targets between 15 and 28. Bin three could represent targets from 29 - 40 and bin four could be the remainder of conductive targets with CO values of 41 - 50. With the numbers used in these examples, if you passed over a target with a FE value of 12 and a CO value of 44, it would provide the conductive tone you assigned to conductive bin four. If you passed over a target with an ID of 11 – 22, it would provide the tone assigned to conductive bin two. Again, the user can resize and assign tones to each target group (bin). For those of you who enjoyed hunting in Two Tone Ferrous with the E-TRAC, this takes it one step further allowing you to adjust the FE line, and break down the CO targets into four separate groups.
Gold can ID anywhere in the range of 10-09 to 13-30, and possibly outside of this range. Sometimes the Conductive reading can be very low, like 02, so to improve your chances you really have to dig everything including aluminium foil and pull-tabs.
Regarding settings, the standard Beach mode is quite suitable. One thing you can do is to change the Tone ID profile to Ferrous 35. What this does is it will make low conductive jewellery produce a higher tone than it would in Conductive profile, making it easier to recognize. You can also select Combine, and customize the tones to suit your personal preference.
For saltwater beaches, Manual Sensitivity is recommended, unless your beaches have high levels of magnetic mineralization. If your unit is running nice and stable on Sensitivity 18, try to push it a bit higher. In situations where you are actually detecting in the salt water, turn the Seawater setting on.
The other thing some beach combers often do is to open up the discrimination pattern a little. Mainly dropping the ferrous rejection slightly or simply search in Pattern 2 (simply press and release the Detect button). This is highly recommended on beaches with low levels of junk targets. In this case another thing you can try is changing the Audio Response to LONG. This can improve your ability to hear the very faint target response which jewellery can produce.
Watch the approved Community Instructional Video on Editing FindPoints and WayPoints.
Watch the approved Community Instructional Video on How to link photos from your phone to FindPoints.
Watch the approved Community Instructional Video that includes How to record a GeoHunt.
Watch the approved Community Instructional Video that includes How to record a FindPoint or WayPoint.
Watch the approved Community Instructional Video that includes How to enable the GPS function.
Watch the approved Community Instructional Video that includes Turning on Detect screen options.
Watch the approved Community Instructional Video that includes Turning on the large target ID panel.
Watch the approved Community Instructional Video that includes Turning on the Sensitivity panel.
Watch the approved Community Instructional Video that includes Turning on the detect screen navigation tool.
Watch the approved Community Instructional Video that includes Selecting a Search Mode on the CTX 3030.
Watch the approved Community Instructional Video that includes Editing a Search Mode on the CTX 3030.
Watch the approved Community Instructional Video that includes transferring data from a CTX 3030 to XChange 2.
Watch the approved Community Instructional Video that includes Creating a new Collection on XChange 2.
Watch the approved Community Instructional Video that includes Changing XChange 2 preferences.
Watch the approved Community Instructional Video that includes Adjusting Universal settings.
Watch the approved Community Instructional Video that includes Making a new Search Mode in XChange 2.
No, The FBS 2 coils can only be used on the CTX 3030, while FBS coils can only be used on the E-TRAC, Safari and Explorer Series detectors.
MULTI-IQ+ is the next generation of MULTI-IQ technology and provides more power with lower electromagnetic interference (EMI) in built up areas.
This provides superior performance and depth allowing users to find previously undetectable targets in most locations.
MANTICORE'da kullanılan MULTI-IQ+ teknolojisi, daha iyi algılama derinliği, gelişmiş kurtarma hızı, daha fazla hassasiyet ayarı ve kullanıcılara daha fazla bilgi sağlayan gelişmiş bir 2D ayrım ekranı anlamına gelen daha fazla güç ve daha hızlı işlem sağladığından, MANTICORE neredeyse her açıdan EQUINOX dedektörlerinden daha iyi performans gösterecektir. kazmadan önce hedeflere.
Şu anda MANTICORE ile uyumlu başka bobin bulunmamaktadır.
Aksesuar bobinleri yerel Minelab bayinizden satın alınabilir. Size en yakın bayiliği bulmak için lütfen çevrimiçi bayi bulma aracımızı kullanın.
ML105 kulaklıklar, MANTICORE dedektörünüzle birlikte kutuya dahildir ve köpük pedin başınıza oturarak kulağı çevrelediği kulak üstü tip bir kulaklıktır.
ML85 kulaklıklar, köpük pedin kulağınızın dış kısmına oturduğu kulak üstü tip bir kulaklıktır.
TÜM ARAZİ GENEL: Çoğu hedef ve koşul için mükemmel çok yönlü performans. Mükemmel hedef ayrımı ve mükemmel çöp reddi sağlar.
TÜM ARAZİDE HIZLI: Mükemmel hedef ayrımı ve iyi koku reddi sağlayan artırılmış kurtarma hızı.
TÜM ARAZİLERDE YÜKSEK İLETKENLER: Gümüş para yığınları veya bakır hedefler gibi yüksek iletkenler için mükemmeldir ve iyi hedef kimlik ayrımı sağlar.
TÜM ARAZİLERDE DÜŞÜK İLETKENLER: Dövülmüş paralar veya kaliteli altın takılar gibi küçük/ince nesneler için mükemmeldir.
TÜM ARAZİ ÇÖP REDDETME: Çöplük alanlarda kullanılır. Maksimum demir reddi
PLAJ GENEL: Kuru veya ıslak kumda kullanıldığında çoğu hedef ve plaj koşulu için mükemmel çok yönlü performans. Mükemmel hedef ayrımı ve mükemmel çöp reddi sağlar.
PLAJ DÜŞÜK İLETKENLERİ: Altın zincirler gibi küçük veya ince hedefler için mükemmeldir. Hem kuru hem de ıslak kum için uygundur.
BEACH DEEP: Altın zincirler gibi küçük veya ince hedefler için mükemmel derinlik sağlayan daha düşük kurtarma hızı. Hem kuru hem de ıslak kum için uygundur.
PLAJ SÖRFÜ VE DENİZ SUYU: Su altı veya sörf tespiti dahil zorlu tuzlu su koşulları için mükemmeldir.
GOLDFIELD GENERAL: İyi huylu ila orta derecede mineralli topraklardaki küçük külçeler için mükemmeldir. Bu mod, altın külçeleri üzerinde daha iyi bir genel performans sağlar ve kullanıcıların zayıf hedef yanıtlarını duymasına yardımcı olmak için sürekli ses perdesi içerir. Bu mod çöplük alanlar için önerilmez.
Frekans MULTI-IQ+ olarak ayarlandığında, demir içeren hedeflere, demir içermeyen hedeflerle aynı ölçekte bir hedef kimliği atanır; bu, demir içermeyen hedef kimlikleriyle aynı ölçekte gösterilir. Dahili işlemci bir hedefi demir içerikli olarak sınıflandırdığında, dedektör, Hedef Kimlik numarasının altında kırmızı Demir İçerik Göstergesine eşlik eden düşük bir ses tonu çıkaracak ve 2D ekran, hedefin ekranın üstünde veya altında, hedeften uzakta görünecek şekilde gösterecektir. merkezi iletken hat. 
*Resimler yalnızca açıklama amaçlıdır.*
Bazı madeni paralara benzer, demirli ve iletken özelliklerin bir kombinasyonuna sahip olan karmaşık demirli hedefler genellikle 2D ekranın alt yarısında görünecektir.
Ekranın üst kısmında daha büyük demir içeren hedefler görünecektir. 
İletkenlik özelliği yüksek olan büyük cıvatalar gibi silindirik şekilli bazı büyük demirli hedefler de olabilir, bu tür hedefler hem demirli hem de demirsiz bölgelerde hedef izi gösterebilir.
*Resimler yalnızca açıklama amaçlıdır.*
Ayrımcılık, kullanıcıların bireysel veya grup hedef kimliklerini kabul etmesine veya reddetmesine olanak tanır. Ayrım ayarlandığında, hem demir içeren hem de demir içermeyen hedef kimliklerinde değişiklikler yapılır. Bu, seçilen hedef kimliğinin hem demir içeren hem de demir içermeyen kısmını grileştiren dikey bir çizgi olarak gösterilir.
Demir içeriği limitleri, kullanıcıların, neyin demir içeren veya demir içermeyen bir hedef olarak tespit edildiğini belirlemek için dedektör parametrelerini ayarlamasına olanak tanır. Bunlar 2D ekranın hem üst hem de alt bölümlerinde ayarlanabilir.
*Resimler yalnızca açıklama amaçlıdır.*
Genel olarak Multi, bir dedektör kullanıldığında tekli frekanslardan daha üstündür. Ancak belirli bir frekansın benzersiz bir avantaja sahip olduğu özel durumlar da olabilir.
*Tek frekanslar kullanıldığında Demir İçeriği Limitlerinin devre dışı bırakılacağını ve demir içeren hedeflerin 1'den 19'a kadar bir hedef kimliği sağlayacağını ve ekranda kırmızı bir demir içeriği göstergesi göstereceğini lütfen unutmayın*
Tipik çalışma süresi, tam şarjdan itibaren yaklaşık 10 saattir . MANTICORE dedektörüne doğrudan 0,5A veya 2A (@ 5V) çıkış özelliğini destekleyen herhangi bir USB Güç Bankasından da güç verilebilir. Bu, yalnızca kullanılan güç bankalarıyla sınırlı olan sürekli bir çalışma süresini etkili bir şekilde sağlar.
*MANTICORE dedektörünüzü bir USB güç bankasına bağlıyken su altında KULLANAMAZSINIZ*
MANTICORE dedektörü, USB 2.0 standardına uygun cihazlardan şarj etmeyi destekler. QuickCharge™, Qualcomm tarafından geliştirilen, daha yüksek voltaj kullanan ve MANTICORE dedektörleriyle uyumlu olmayan tescilli bir standarttır .
Tamamen düz durumdan %100'e kadar olan şarj süresi, yüksek kapasiteli bir şarj cihazıyla (>1,7A @ 5V) şarj edildiğinde yaklaşık 7 saattir .
Pilinizi şarj etmek için USB pil şarjı 1.2 (BC1.2) ile uyumlu herhangi bir standart USB bağlantı noktası kullanılabilir, ancak daha düşük güç seçenekleri kullanıldığında şarj süreleri daha uzun olabilir.
Tüm pillerin ömrü, genellikle kullanıcı tarafından bir dereceye kadar kontrol edilebilen bir dizi faktöre bağlıdır; sıcaklık, depolandığındaki şarj seviyeleri, şarj döngüleri vb. gibi. Li-İyon pillerin ömrünün azalmasının en yaygın nedeni, tam şarjlı bir pili yüksek sıcaklıklarda tutmaktır.
Dedektörlerimizde kullanılan tüm bileşenlerde olduğu gibi, yalnızca modern, yüksek kaliteli bileşenleri sorumlu satıcılardan temin ediyoruz. Kullanıcıların yıllar boyu kullanımda herhangi bir pil sorunu yaşamasını beklemiyoruz. Her ikisi de Li-ION pil kullanan CTX 3030 ve GPZ 7000 dedektörlerle olan deneyimimiz, kullanıcıların büyük çoğunluğunun hiçbir zaman yedek pil satın alma ihtiyacı duymamış olmasıdır.
MANTICORE pilini aşağıda açıklandığı gibi şarj ederken yalnızca saygın ve sertifikalı USB Şarj Cihazlarını kullanın:
Sapta bulunan Li-ION pil değiştirilebilir ve bir süre garanti kapsamındadır. Satın alma tarihinden itibaren 6 ay. Minelab, su geçirmez contanın zarar görmesini ve dedektör garantisinin geçersiz kalmasını önlemek için Yetkili Servis Merkezi kullanılmasını önerir.
Evet, karada arama yaparken herhangi bir sınırlama olmaksızın. Ancak dedektör, şarj sırasında veya bir güç bankasına bağlıyken su altında kullanılmamalıdır.
Evet. Dedektör kullanılıyorsa ve bir USB güç bankası tarafından çalıştırıldığında, güç bankasında yeterli yedek kapasite varsa pil daha yavaş bir hızda şarj olabilir.
Evet. Suda veya kumsalda arama yaptıktan sonra dedektörü temiz tatlı suyla yıkamak iyi bir uygulamadır. Dedektörü temizlemek için asla aşındırıcı veya solvent kullanmayın.
Hayır. Su geçirmez contalar da dahil olmak üzere dedektörün herhangi bir parçasını yağlamak veya greslemek gerekli değildir. Petrol bazlı herhangi bir gresin kullanılması su geçirmez contalara zarar verecek ve garantiyi geçersiz kılacaktır.
Derin suda veya tamamen suya batmışsa, yalnızca Minelab Su Geçirmez Kulaklıklarını kullanmanızı öneririz. Bunlar, MANTICORE ile birlikte kullanıldığında su geçirmez bir conta oluşturan özel olarak tasarlanmış bir konektöre sahiptir. Bu kulaklıklar, yerel Minelab bayinizden satın alınabilecek bir aksesuar olarak mevcuttur.
Hardwired coils are more reliable for deep diving detectors.
No, 8 x 1.2V is only 9.6V, and these detectors require 12V to function.
Check to ensure the battery is fully charged. A low battery causes the threshold to get very loud and the response becomes erratic.
Salt, sand and grit will accumulate on the Excalibur II. So make sure you thoroughly rinse it with fresh water after use, including the coil cover, shafts and battery pack. Don't forget the vent holes on each headphone diaphragm as these need to be clear if used for diving purposes to allow for ear equalisation.
The Multi-IQ engine in all EQUINOX series is the same, there are however processor enhancements in the EQUINOX 700 and EQUINOX 900 that allow the detector to provide users with better Iron Bias, target separation and discrimination depth.
Park 1 (General/Coins)
Park 1 is optimised for modern coins and larger jewellery with a default discrimination pattern set to reject many common aluminium foil-like targets. Therefore, this is the ideal Profile to start with to learn EQUINOX before experimenting with the other Modes and more specialist settings. Park 1 Multi-IQ processes a lower frequency weighting of the multi-frequency signal, as well as using algorithms that maximise ground balancing for soil to achieve the best signal-to-noise ratio. Hence Park 1 is most suited for general detecting and coin hunting.
Park 2 (Fine jewellery)
Park 2 is ideal for smaller targets in trash-infested (including ferrous trash) locations. It will detect a wider range of targets including low conductor (or higher frequency) targets, e.g. fine jewellery. All non-ferrous targets are accepted by default. Recovery Speed is increased to clearly identify good targets masked by iron trash. Target Tone is set to maximum to provide as much target information as possible via audio. Park 2 Multi-IQ processes a higher frequency weighted multi-frequency signal while ground balancing for soil.
Field 1 (Coins and Artefacts)
Field 1 is for general hunting with high trash rejection. This assists in locating desired targets more easily. The default discrimination pattern is set to reject most coke signals. The first Tone Break is set so that the coke signals will produce the same low tone as ferrous targets. Field 1 Multi-IQ processes a lower frequency weighted multi-frequency signal, as well as using algorithms that maximise ground balancing for soil, to achieve the best signal to noise ratio. Hence being most suited for general detecting and coin hunting.
Field 2 (Fine coins and Artefacts)
Field 2 suits locations with high target and trash densities. It will better detect small hammered coins on their edge or at greater depth. The default discrimination pattern is set to reject most coke signals. Target Tone is set to maximum to enhance audio identification and Recovery Speed is faster. The first Tone Break has been set so that the coke signals will produce the same low tone as ferrous targets. Field 2 Multi-IQ processes a higher frequency weighted multi-frequency signal while ground balancing for soil.
Beach 1
Beach 1 is most useful for detecting in wet or dry beach sand and also in shallow water where conductive salt signals are prevalent. It has good sensitivity to coins and small/large jewellery. Beach 1 reduces the salt signal, while maintaining high transmit power, and still being sensitive to desirable targets. Beach 1 Multi-IQ processes a low frequency weighted multi-frequency signal, and uses special algorithms to maximise ground balancing for salt
Beach 2
Beach 2 gives the best results when either wading or shallow diving with the coil and/or detector fully submerged. In these instances, there is a very strong salt signal present, so Beach 2 has a lower transmit power, which results in much less noise. This profile may also be useful in dry conditions where there are extremely high ground noise levels. Beach 2 Multi-IQ processes a very low weighted multi-frequency combination, using the same algorithms as Beach 1 to maximise ground balancing for salt.
Multi-IQ (EQUINOX 800 & 900 only)
Gold 1
Gold 1 is suitable for searching for small gold nuggets in ‘mild’ ground. Most goldfield locations have a variable level of iron mineralisation that will require an ongoing Ground Balance adjustment, therefore Tracking Ground Balance is the default setting. The audio Threshold Level and Threshold Pitch are optimised for hunting for gold nuggets. Gold 1 Multi-IQ processes a high frequency weighted multi-frequency signal, while ground balancing for mineralised soil.
Gold 2
Gold 2 is best for searching for deeper gold nuggets in ‘difficult’ ground conditions. Gold 2 has a lower Recovery Speed, which will increase detection depth. However, more ground noise in more heavily mineralised grounds may result. Tracking Ground Balance is the default setting. The audio Threshold Level and Threshold Pitch are optimised for hunting for gold nuggets. Gold 2 Multi-IQ processes a high frequency weighted multifrequency signal, while ground balancing for mineralised soil.
EQUINOX 700
• Weight has been decreased to 1.27kg (2.8lb)
• Waterproof to 5m (IP68)
• Three piece collapsible shaft now 144cm - 61cm (56.7" - 24")
• All carbon fibre shafts
• New, easily adjustable armrest
• 119 Target ID Range (-19 to 99)
• 119 discrimination notch segments
• "Depth Pitch" audio option in all modes
• Improved target separation
• Improved ferrous rejection
• Red LCD backlight
• Keypad backlight
• LED flashlight
• Handle vibration target indication
EQUINOX 900
• All above features
• Greater Sensitivity range 1 - 28
• Includes EQX06 6" waterproof DD coil
The new carbon fiber shaft design allows users to pack the detector down to 61cm (24 in) and has a full extension of 144cm (56.7 in)
Depth performance will differ depending on conditions and detector settings. Beach performance is better overall. Enhancements have been made to improve recovery speed, target separation and discrimination depth allowing users to have solid target IDs at better depths. EQUINOX 900 comes with 28 levels of sensitivity allowing more depth where environmental conditions allow the sensitivity to be turned up.
What are the frequency differences between the EQUINOX 600, 700, 800 & 900?
The EQUINOX 600 and 700 offer a choice of 4 single selectable frequencies:
• 4kHz
• 5 kHz
• 10 kHz
• 15 kHz
The EQUINOX 800 and 900 offers the choice of 6 single selectable frequencies:
• 4kHz
• 5 kHz
• 10 kHz
• 15 kHz
• 20 kHz
• 40 kHz
Gold Mode is designed to enhance performance on small gold nuggets in mineralized ground. It does so primarily by using different audio processing so that targets respond both in volume and pitch. The Gold Mode will be of interest to gold prospectors but has less application for other uses.
While the EQUINOX 600 and 700 do not have a dedicated Gold prospecting mode. Multi-IQ is so good in both Park 2 and Field 2, that these profiles are as good, or better, at finding gold nuggets than many dedicated single-frequency gold detectors. Multi-IQ provides very stable ID’s which is great for choosing what targets to dig in a goldfield.
Iron Bias is a setting that lets you choose how you want iron in the ground to sound. If you have a low setting, more of the iron will come through as a good target to dig up. This will also give you the best chance of finding any valuable non-ferrous targets nestled among the iron.
However, if you desire to hear less false audio sounds from the iron in the ground, try increasing the Iron Bias setting.
The Iron Bias in the EQUINOX 700 and EQUINOX 900 has had some changes to improve discrimination depth.
EQUINOX 600 and 800 have the option to choose either FE Iron Bias or F2 Iron Bias. FE Iron Bias will provide control over the target ID response. F2 Iron Bias will provide tone and target ID response adjustment for a wider range of ferrous targets.
Iron Bias in the EQUINOX 700 and EQUINOX 900 is based off the F2 Iron Bias in the EQUINOX 600 and EQUINOX 800 but allows even better overall depth detection and target separation. Because of this there is no F2 option available in the EQUINOX 700 or EQUINOX 900.
Yes, Coiltek Coils manufacture Minelab approved aftermarket coils for the EQUINOX and X-TERRA-PRO detectors.
No, they have different technology requirements and are not compatible. Only Minelab EQX coils are compatible with EQUINOX series detectors.
Having a larger target ID scale allows the detector to provide the user with more information on the target prior to digging it. This allows users to identify more targets individually which will help determine if the target is valuable or trash.
In general, Multi is superior to the single frequencies when using an EQUINOX. However, there may be specialised situations where a particular frequency has a unique advantage. The EQUINOX Series offers users simultaneous Multi-Frequency plus a wide range of single selectable frequencies for specialist situations.
Yes, there is no need to perform a full factory reset. Individual Search Profiles can easily be returned to their factory preset settings. Only the local settings will be reset and any global settings will remain in their last-use state.
Beach Mode automatically senses black sand and reduces the transmit power to ensure that targets can still be detected without overloading occurring. When black sand is sensed, the Beach Overload Indicator will appear on the LCD. When this icon disappears, full transmit power automatically resumes.
Depth Pitch is an audio mode that provides a continuous pitch audio with no threshold tone. It provides separate audio for ferrous and non-ferrous targets with a variable pitch.
Small or deep targets providing a weaker signal will have a lower pitch.
Large or shallow targets providing a stronger signal will have a higher pitch.
EQUINOX 700 and EQUINOX 900 have been designed to handle harsh outdoor environments. Our testing includes drop tests up to 1m, flex and water ingress testing. Both models are IP68 rated and can be submerged up to 5m (16ft)
Middle and Lower shafts can be mixed. They are not identical in size so they may not provide an exact fit. Upper shafts cannot be changed as the physical mounting point of the control pod is different.
Yes. The supplied magnetic USB charge cable can be used on all EQUINOX models, MANTICORE and X-TERRA PRO detectors.
The charge time, from completely flat to 100%, is approximately 4 hours when charged with a high capacity charger (>1.7A @ 5V).
Longevity for all batteries depends on a number of factors that are often controllable to some degree by the user; such as temperature, charge levels when stored, charge cycles etc. The most common cause of reduced life of Li-ION batteries is keeping a fully charged battery at elevated temperatures.
As with all components used in our detectors, we stringently source only modern high quality components from responsible vendors. We do not expect users to experience any battery issues over years of use. Our experience with the CTX 3030 and GPZ 7000 detectors which both use Li-ION batteries is that the vast majority of users have never needed to purchase a replacement battery.
• Avoid charging or using in extreme temperatures.
• Avoid rapid extreme temperature swings.
• Use only Minelab or Minelab recommended USB chargers and avoid so-called ultrafast chargers from third-parties that claim to fully charge Li-ION batteries in less than one hour.
• Before storing the detector for prolonged periods, the battery should be charged to approximately 50-60%. On the EQUINOX Battery Status Indicator, 2-bars is the optimum charge for prolonged storage. Maintaining the 2-bar charge periodically during extended storage is also advisable. Extended storage in temperatures less than 30oC (86’F) will also minimize degradation to Li-ION battery life
Use only reputable and certified USB Chargers when charging the EQUINOX battery as detailed below:
Typical runtime, from a full charge using wired headphones, is approximately 12 hours. The EQUINOX Series detectors can also be powered directly from any USB Power Bank that supports 0.5A or 2A (@ 5V) output capability. This effectively gives a continuous runtime only limited by the power banks being used.
The EQUINOX detectors support charging from devices that comply to the USB 2.0 standard. QuickCharge™ is a proprietary standard develop by Qualcomm that uses a higher voltage and is not compatible with EQUINOX detectors.
Sapta bulunan Li-ION pil değiştirilebilir ve satın alma tarihinden itibaren 6 ay süreyle garanti kapsamındadır. Minelab, su geçirmez contanın zarar görmesini ve dedektör garantisinin geçersiz kalmasını önlemek için Yetkili Servis Merkezi kullanılmasını önerir.
*EQUINOX 600 ve EQUINOX 800 pilleri, EQUINOX 700 veya EQUINOX 900 ile uyumlu değildir.
Yes, when detecting on land, without any limitations. However, the detector must not be used underwater whilst charging or when connected to a power bank.
Yes. If the detector is being used, when powered by a USB power bank, the battery may charge at a slower rate if there is enough spare capacity in the power bank.
Yes. Connecting the WM 08 to a power bank will allow you to continue to use it even if the battery is low/flat. The power bank will charge the WM 08, which will continue operating as normal.
*Please note that the WM08 is not compatible with the EQUINOX 700 OR EQUINOX 900
No. They are separate wireless technologies and only one can be used at any one time.
*Please note that the WM08 and Bluetooth headphones are not compatible with the EQUINOX 700 OR EQUINOX 900
Re-pairing will be required if a different wireless device has been connected to the Equinox 600 or Equinox 800 (e.g. WM 08), or following a detector factory reset.
AUDIO
Bluetooth® Hearing Aids are largely intended to allow the wearer to intentionally connect to other Bluetooth® compatible devices, such as phones and audio streams. They enable the wearer to stream audio on-the-go without having to remove the hearing aid and insert earbuds.
The EQUINOX 600 and EQUINOX 800 detectors are Bluetooth® compatible devices.
While there are various different types of streaming audio hearing aids available on the market, if the hearing aid supports Bluetooth® A2DP or Bluetooth® aptX-Low Latency™ then it will be compatible with the EQUINOX 600 and EQUINOX 800 detectors.
Pairing with the EQUINOX 600 or EQUINOX 800 is achieved by pressing and holding the Wireless button on the side of the Control Unit for 5 seconds.
While pairing is being performed the Wireless icon on the LCD will flash rapidly for 15 seconds. After 15 seconds the Bluetooth® icon will start flashing on the LCD to indicate a Bluetooth device is being paired.
The initial pairing may take up to 5 minutes. During the pairing process the user should not press the Wireless button as this will stop the pairing process.
Once paired, the EQUINOX 600 or EQUINOX 800 will display a solid Bluetooth® icon on the top right of the LCD. If the hearing aid is aptX-Low Latency™ Bluetooth compatible the ‘+’ icon will also be displayed.
Consult your Hearing Aid User Manual for additional pairing instructions specific to your hearing aid.
*Please note that EQUINOX 700 and EQUINOX 900 are not currently compatible with hearing aids.
Yes, the Equinox 600 can still pair to Bluetooth A2DP or Bluetooth aptX-Low Latency headphones.
Yes. It is good practice to wash the detector with clean fresh water after detecting in water or on the beach. Never use abrasives or solvents to clean the detector.
Whenever washing or using your detector underwater always ensure that the plastic bung on the rear of the control pod is firmly screwed into the headphone jack.
No. It is not necessary to lubricate or grease any part of the detector, including the waterproof seals. Using any petroleum-based grease will damage the waterproof seals and void the warranty.
If deep wading or fully submerged, we recommend using only Minelab Waterproof EQUINOX Headphones. These have a specially engineered connector that forms a waterproof seal when used with the EQUINOX. These headphones are available as an accessory from your local Minelab authorised dealership (Part Number: 3011-0372)
Yes, the MULTI-IQ technology in the X-TERRA ELITE is the same as the MULTI-IQ technology used in other MINELAB metal detectors.
X-TERRA ELITE includes a 15kHz single frequency option for the Park and Field modes.
X-TERRA ELITE, mükemmel performansa sahip, uygun fiyatlı bir dedektör arayan kararlı dedektörler için tasarlanmıştır. Kullanıcılar, dedektör uzmanlarının algılama performansını ayarlamasına olanak tanıyan daha fazla kontrol ve ayar ayarına sahiptir. X-TERRA ELITE, 5 metreye (15 feet) kadar su geçirmezdir ve şu anda piyasada bulunan diğer tek frekanslı dedektörlerle karşılaştırıldığında üstün performans sağlar.
VANQUISH serisi, mükemmel performansa sahip olacak şekilde tasarlanmış ancak yine de minimum ayar ayarlamalarıyla kullanımı çok kolay olacak şekilde tasarlanmış, aç ve çalıştır tipi bir dedektördür. MULTI-IQ işlemci sizin için tüm zor işleri yaptığı için bu mümkündür.
VANQUISH dedektörleri yeni başlayanlar için, X-TERRA ELITE dedektörü ise başlangıç seviyesindeki bir dedektörden yükseltme yapmak isteyen orta düzey dedektörler için önerilmektedir.
V*X veya EQUINOX serisi bobinler X-TERRA ELITE ile kullanılabilir ancak önceki X-TERRA 305, 505 ve 705 serisi bobinler dahil olmak üzere başka hiçbir Minelab markalı bobinler kullanılamaz.
X-TERRA ELITE, kutuda bir V12X 12” Eliptik Çift-D bobin ile birlikte gelir; aşağıdaki aksesuar bobinlerini yerel Minelab bayinizden satın alabilirsiniz.
X-TERRA ELITE will out-perform the VANQUISH and X-TERRA PRO detectors in all terrains on most targets. Performance may be similar in some circumstances but will differ depending on ground mineralisation levels but more specifically the type of metal each target consists of.
The X-TERRA ELITE provides unprecedented performance in salty conditions. There are 2 beach modes to ensure stability in both wet and dry salty environments.
Yes, you can purchase the Minelab WM09 wireless module, ML85 headphones or ML105 headphones as all of these are compatible with the X-TERRA ELITE. (note that the X-TERRA ELITE EXPEDITION model includes the ML85 headphones in the box)
X-TERRA ELITE, BLUETOOTH'un güncel sürümleriyle uyumlu olmayan özel bir kablosuz ses kullanır. Minelab ML85 veya ML105 kulaklıklar ve WM09 kablosuz modülü, X-TERRA ELITE ile uyumludur ve yerel yetkili Minelab bayinizden temin edilebilir.
Park 1 provides a default MULTI-IQ transmit frequency and is optimised for detecting modern coins and larger jewellery. This is a good mode to learn the X-TERRA ELITE before experimenting with other settings.
Park 2 provides a default MULTI-IQ transmit frequency and is optimised for detecting fine jewellery and smaller targets in trash infested areas. Recovery speed in Park 2 is increased to clearly identify good targets masked by iron trash.
Field 1 provides a default MULTI-IQ transmit frequency and is optimised for detecting modern coins and general detecting. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Field 2 provides a default MULTI-IQ transmit frequency and is optimised for locations with high target and trash densities. This mode is great for coins on edge or sitting at greater depths. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Beach 1 provides a default MULTI-IQ transmit frequency and is optimised for dry and wet sand. Beach 1 mode has a lower recovery speed for better depth across all targets and is good for detecting coins and small to large jewellery.
Beach 2 provides a default MULTI-IQ transmit frequency and is optimised for underwater usage where a very strong salt signal is present. To compensate for the high salt content Beach 2 has a lower transmit power. Beach 2 can also be used in dry soils that have a high salt content.
Yes, there is no need to perform a full factory reset. Individual Search Profiles can easily be returned to their factory preset settings. Only the local settings will be reset and any global settings will remain in their last-use state.
Typical runtime, from a full charge using wired headphones, is approximately 12 hours. The X-TERRA ELITE detector can also be powered directly from any USB Power Bank that supports 0.5A or 2A (@ 5V) output capability. This effectively gives a continuous runtime only limited by the capacity of the power bank.
The X-TERRA ELITE detector supports charging from devices that comply to the USB 2.0 standard. QuickCharge™ is a proprietary standard develop by Qualcomm that uses a higher voltage and is not compatible with X-TERRA ELITE detectors.
The charge time, from completely flat to 100%, is approximately 4 hours when charged with a high capacity charger (>1.7A @ 5V).
Longevity for all batteries depends on a number of factors that are often controllable to some degree by the user; such as temperature, charge levels when stored, charge cycles etc. The most common cause of reduced life of Li-ION batteries is keeping a fully charged battery at elevated temperatures.
As with all components used in our detectors, we stringently source only modern high quality components from responsible vendors. We do not expect users to experience any battery issues over years of use. Our experience with the CTX 3030 and GPZ 7000 detectors which both use Li-ION batteries is that the vast majority of users have never needed to purchase a replacement battery.
Use only reputable and certified USB Chargers when charging the X-TERRA ELITE battery as detailed below:
The Li-ION battery contained in the handle is replaceable and covered under warranty for a period of 6 months from the date of purchase. Minelab recommends using an Authorised Service Centre to avoid potentially damaging the waterproof seal and voiding the detector warranty.
Yes, when detecting on land, without any limitations. However, the detector must not be used underwater whilst charging or when connected to a power bank.
Yes. If the detector is being used, when powered by a USB power bank, the battery may charge at a slower rate if there is enough spare capacity in the power bank.
Yes. Connecting the X-TERRA ELITE to a USB power bank will allow you to continue to use the detector even if the battery is low/flat. The power bank will charge the detector if there is any residue power to charge the battery.
Evet. Suda veya kumsalda arama yaptıktan sonra dedektörü temiz tatlı suyla yıkamak iyi bir uygulamadır. Dedektörü temizlemek için asla aşındırıcı veya solvent kullanmayın.
Dedektörünüzü su altında yıkarken daima kontrol bölmesinin arkasındaki plastik tapanın kulaklık jakına sıkı bir şekilde vidalandığından emin olun.
No. It is not necessary to lubricate or grease any part of the detector, including the waterproof seals. Using any petroleum-based grease will damage the waterproof seals and void the warranty.
If deep wading or fully submerged, we recommend using only Minelab Waterproof Headphones. These have a specially engineered connector that forms a waterproof seal when used with the X-TERRA ELITE.
VANQUISH depth performance is similar but not quite as deep as the EQUINOX. However, EQUINOX detectors are more configurable for varying conditions.
Minelab does not publish the exact frequencies of Multi-IQ technology used in the VANQUISH Series. These frequencies are similar to the Multi-IQ mode in the EQUINOX Series.
The VANQUISH Series detectors only use Multi-IQ (simultaneous multi-frequency) technology.
Target IDs on VANQUISH are the same as the Target IDs on EQUINOX.
Recovery speed varies depending on the mode selected.
The Custom mode is programmable. If you program custom mode, it will adopt the recovery speed from the mode you program it to, e.g. coin mode = fast recovery speed, jewellery = medium recovery speed, relic = slow recovery speed.
When the detector is switched off, discrimination patterns in coin, jewellery & relic modes are all reset. Custom mode will keep its saved discrimination pattern.
There are three coils available for VANQUISH. These are:
The VANQUISH Series requires x4 AA batteries and is compatible with both rechargeable and non-rechargeable batteries. The battery level indicator shows the current battery level. Lift the battery cover off the control box to replace the batteries.
The VANQUISH 540 and 540 Pro-Pack come with x4 AA NiMH rechargeable cells and a charger. The VANQUISH 340 and 440 can also operate with rechargeable batteries. Minelab recommends only NiMH rechargeable batteries or non-rechargeable AA alkaline batteries. Batteries rated between 1.2v – 1.5v are acceptable. If the battery has a voltage higher than 1.5v, it can damage the detector.
AA rechargeable NiMH batteries provide a run-time of approximately 11 hours using factory default settings.
Non-rechargeable, high-quality AA alkaline batteries provide a run-time of approximately 10 hours.
No. VANQUISH coils cannot be used on EQUINOX, and EQUINOX coils cannot be used on VANQUISH.
The VANQUISH control box is not submersible. The coils are fully waterproof up to 1 m (3 ft).
The temperature specification for the VANQUISH Series is -10C – 40 C (14F – 104 F). The coil is waterproof to 1 m (3 ft), but the control pod cannot be submerged.
No. Pitch or tone breakpoints cannot be adjusted on the VANQUISH Series.
The VANQUISH 540 has a red backlight for detecting in low light situations. The backlight is 'Off' by default at each start-up to reduce battery consumption.
The Multi-IQ technology used in VANQUISH allows the detector to provide stable and reliable target IDs in light of medium mineralised soils found in beaches or parks. As a result, there is no ground balance function available in the VANQUISH Series.
Multi-IQ technology allows VANQUISH to operate on wet beach sand and salt water with much higher performance than a single frequency VLF detector.
VANQUISH 540 can operate with Bluetooth V4.2 or later and Bluetooth aptX Low Latency headphones. VANQUISH 340 & 440 do not have wireless capability.
Yes. Software updates can be found on the Minelab website on the VANQUISH product page 'downloads' section.
VANQUISH Series detectors are under warranty for three years (36 months) from the Date of Purchase. Detailed product warranty information can be found under SUPPORT at minelab.com.
Including battery weight, the VANQUISH 340 and 440 weigh 1.2 kg (2.6 lbs), whereas VANQUISH 540 weighs 1.3 kg (2.9 lbs), as it includes the larger V12 coil.
VANQUISH 540 Pro-Pack contains the same VANQUISH 540 detector but includes the smaller V8 coil and the ML80 Bluetooth aptX Low Latency wireless headphones.
Dedektörü kapattıktan sonra, dedektörü yeniden başlatmayı denemeden önce lütfen en az 2 saniye bekleyin.
Demir Önyargı ayarı, tüm VANQUISH dedektörlerindeki tüm modlarda aynıdır.
Not: VANQUISH 540, EQUINOX'a benzer bir demir sapma tepkisine sahip ayarlanabilir bir Demir Önyargıya sahiptir.
PRO-SWITCH technology is a single frequency VLF technology that allows the user to switch transmit frequencies at the touch of a button to optimise performance.
Changing frequency gives detectorists the ability to adjust frequencies to move away from noise or optimise detection ability when hunting for specific metal targets.
Park and Field modes have 5kHz, 10kHz and 15kHz selectable frequencies. Beach modes have an 8kHz single frequency for high salt mineralisation.
MULTI-IQ will provide superior results when compared to PRO-SWITCH. There may be situations where the PRO-SWITCH technology can perform equally as well as MULTI-IQ. This will depend on how the user has optimised the detector settings.
Multi-IQ will provide maximum performance in all situations as the internal processor does all the hard work. PRO-SWITCH relies on the user to ensure the detector is set to its optimal performance capability.
VANQUISH detectors with MULTI-IQ are a switch-on and go type detector designed to have excellent performance but still be very easy to use with minimal setting adjustments. This is possible as the MULTI-IQ processor does all the hard work for you.
X-TERRA PRO is a high performing single frequency detector designed for the more committed detectorist looking for a well-priced detector with great performance. Users have the ability to adjust transmit frequency which provides more control allowing detectorists to tune the detection performance when hunting for specific targets. The X-TERRA PRO is waterproof to 5 meters (15 feet) and provides superior performance when compared to any other single frequency detector currently on the market.
Target ID’s on the X-TERRA PRO will generally not be quite as stable as MULTI-IQ target ID’s and MULTI-IQ detectors will generally provide superior performance when in conductive (salty) soils.
The X-TERRA PRO comes with a V12X 12” Elliptical Double-D coil in the box, you can purchase the below accessory coils from your local Minelab dealership. Any coil that is compatible with the EQUINOX detectors is also compatible with the X-TERRA PRO.
10kHz is the best all-round frequency to start detecting with as it provides good depth and sensitivity across a range of different targets.
It is expected when running a lower transmit frequency on the X-TERRA PRO that performance on high conductors containing silver or copper will provide similar depths to MULTI-IQ detectors.
It is expected when running a higher transmit frequency on the X-TERRA PRO that performance on lower conductors containing gold will provide similar depths to MULTI-IQ detectors.
At the beach in salty conditions most single frequency detectors struggle with the mineralisation. The X-TERRA PRO provides unprecedented performance for a single frequency VLF detector in salty conditions.
Yes, there is no need to perform a full factory reset. Individual Search Profiles can easily be returned to their factory preset settings. Only the local settings will be reset and any global settings will remain in their last-use state.
Yes, you can purchase the Minelab ML85 headphones, ML105 headphones or the WM09 wireless module. These are all compatible with the X-TERRA PRO.
There are currently no aftermarket wireless headphones available for the X-TERRA PRO.
The X-TERRA PRO uses a proprietary wireless audio that is not compatible with any current versions of BLUETOOTH. The Minelab ML85 or ML105 headphones and WM09 wireless module are compatible with the X-TERRA PRO and are available from your local authorised Minelab dealership.
Park 1 provides a default 10kHz transmit frequency and is optimised for detecting modern coins and larger jewellery. This is a good mode to learn the X-TERRA PRO before experimenting with other settings.
Park 2 provides a default 15kHz transmit frequency and is optimised for detecting fine jewellery and smaller targets in trash infested areas. Recovery speed in Park 2 is increased to clearly identify good targets masked by iron trash.
Field 1 provides a default 10kHz transmit frequency and is optimised for detecting modern coins and general detecting. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Field 2 provides a default 15kHz transmit frequency and is optimised for locations with high target and trash densities. This mode is great for coins on edge or sitting at greater depths. It has a high trash rejection which makes it an ideal detect mode for areas containing coke.
Beach 1 provides a default 8kHz transmit frequency and is optimised for dry and wet sand. Beach 1 mode has a lower recovery speed for better depth across all targets and is good for detecting coins and small to large jewellery.
Beach 2 provides a default 8kHz transmit frequency and is optimised for underwater usage where a very strong salt signal is present. To compensate for the high salt content Beach 2 has a lower transmit power. Beach 2 has a higher recovery speed to aid in saltwater rejection. It can also be used in dry soils that are conductive (salty).
Typical runtime, from a full charge using wired headphones, is approximately 16 hours. The X-TERRA PRO detector can also be powered directly from any USB Power Bank that supports 0.5A or 2A (@ 5V) output capability. This effectively gives a continuous runtime only limited by the capacity of the power bank.
The X-TERRA PRO detector supports charging from devices that comply to the USB 2.0 standard. QuickCharge™ is a proprietary standard develop by Qualcomm that uses a higher voltage and is not compatible with X-TERRA PRO detectors.
The charge time, from completely flat to 100%, is approximately 4 hours when charged with a high capacity charger (>1.7A @ 5V).
Longevity for all batteries depends on a number of factors that are often controllable to some degree by the user; such as temperature, charge levels when stored, charge cycles etc. The most common cause of reduced life of Li-ION batteries is keeping a fully charged battery at elevated temperatures.
As with all components used in our detectors, we stringently source only modern high quality components from responsible vendors. We do not expect users to experience any battery issues over years of use. Our experience with the CTX 3030 and GPZ 7000 detectors which both use Li-ION batteries is that the vast majority of users have never needed to purchase a replacement battery.
Use only reputable and certified USB Chargers when charging the X-TERRA PRO battery as detailed below:
Sapta bulunan Li-ION pil değiştirilebilir ve bir süre garanti kapsamındadır. Satın alma tarihinden itibaren 6 ay. Minelab, su geçirmez contanın hasar görmesini ve dedektör garantisinin geçersiz kalmasını önlemek için Yetkili Servis Merkezi kullanılmasını önerir.
Yes, when detecting on land, without any limitations. However, the detector must not be used underwater whilst charging or when connected to a power bank.
Yes. If the detector is being used, when powered by a USB power bank, the battery may charge at a slower rate if there is enough spare capacity in the power bank.
Yes. It is good practice to wash the detector with clean fresh water after detecting in water or on the beach. Never use abrasives or solvents to clean the detector.
Whenever washing or using your detector underwater always ensure that the plastic bung on the rear of the control pod is firmly screwed into the headphone jack.
No. It is not necessary to lubricate or grease any part of the detector, including the waterproof seals. Using any petroleum-based grease will damage the waterproof seals and void the warranty.
If deep wading or fully submerged, we recommend using only Minelab Waterproof Headphones. These have a specially engineered connector that forms a waterproof seal when used with the X-TERRA PRO. These headphones are available as an accessory (Part Number: 3011-0372)
No, the detection coil that is included with your GO-FIND detector is designed to provide the best performance for that specific model and cannot be changed.
The battery compartment is in the handle of the GO-FIND. On the rear of the handle, you will see a small tab. Gently pull this tab down and then lift the battery compartment lid to access the batteries.
Yes, the GO-FIND series can operate with rechargeable 1.2volt Ni-MH rechargeable batteries. You can only use batteries that have a 1.2 volt or 1.5volt rating. Most AA Lithium batteries have a higher voltage and cannot be used as they exceed the maximum voltage rating for the detector. Using Lithium batteries that exceed the maximum voltage rating can damage the internal electronics of the detector. This type of damage is not covered under warranty.
The detection coil on the GO-FIND series is waterproof to 60cm (2ft) and can be washed. The screen pod should never be washed or submerged in water as it is not waterproof. To clean the screen pod wipe it with a damp cloth.
Yes, the GO-FIND detectors utilise Minelab’s Easy-Trak ground balance technology which automatically senses salt mineralisation in the ground and adjusts the detector to ensure constant smooth usage when detecting in beaches or parks.
Wireless headphones can be used but they cannot be paired directly to your detector. You will need to connect your wireless headphones to your smartphone and then connect your GO-FIND 44 or 66 to your smartphone via the GO-FIND app. GO-FIND 11 or 22 do not have Bluetooth capability and cannot connect to the GO-FIND app or wireless headphones.
In your Android phone Google Play Store & Apple iPhone App Store Search for Minelab GO-FIND
GO-FIND by Minelab Electronics Pty Ltd will be 1st – 2nd in search result.
The Pro App function is FREE for GO-FIND 66 detectors. Download the same GO-FIND App for FREE. When this GO-FIND App is paired with a GO-FIND 66, the App will activate full Pro App functions.
Download the same GO-FIND App for FREE. When this GO-FIND App is paired with a GO-FIND 44, the App will activate basic App functions.
Download the same GO-FIND App for FREE. When this GO-FIND App is paired with a GO-FIND 44, the App will activate basic App functions. It is optional to upgrade your Basic App functions to Pro App functions, just like how it used on a GO-FIND 66. In-app purchase is available for upgrading.
For the first time use, you need to pair GO-FIND 44/66 with your mobile device:
See also:
In GO-FIND App, the is help (?) button on the bottom right corner. Click to view Bluetooth pairing guide and Bluetooth connection guide.
No, after the pairing for the first time use. Your next time use should just require a short press to turn on Bluetooth function.
You can now use App with the detector
Android 11 or later with Bluetooth Lower Energy hardware
iPhone iOS 8.0 or later with Bluetooth Lower Energy hardware
No, the X-TERRA VOYAGER uses different technology to other detectors. You can only use the coil that is supplied in the box with the detector.
The X-TERRA VOYAGER does not have any accessory coils currently available.
The depth gauge will provide an approximate indication of depth and should only be used as a guide as large or small metals will cause the gauge to become inaccurate. A coin sized object will provide the below estimated depths.
1 arrow = 1” (25mm)
2 arrows = 3” (75mm)
3 arrows = 5” (125mm)
4 arrows = 6” (150mm)
5 arrows = >6” (>150mm)
The X-TERRA VOYAGER does not have wireless capability. You can use a Bluetooth wireless transmit module with the detector. These are not available from Minelab and will have to be purchased separately.
All Metal allows the detector to detect all metal types. When in all metal mode there will be no discrimination of any metal types.
Custom provides users the ability to discriminate any of the target group icons at the top of the screen. You simply navigate through to the desired target group and the icon will flash for a few seconds and then it will disappear. All target ID’s in this target group will now be discriminated out.
To detect the discriminated target group simply navigate away from the target group and then navigate back to the desired target group. The icon will flash for a few seconds and then appear. All target ID’s in the target group will now detect again.
Jewelry provides discrimination pattern that ignores most iron/ferrous junk. You will also find coins, relics and other non-ferrous metals. This mode is good for trashy environments.
Learn allows users to detect 1 specific target group. You simply need to wave the desired metal over the detection coil, the detector will then learn this target ID and accept only targets ID’s within that target group.
Typical runtime, when using new high quality 9-volt alkaline batteries is 20 hours.
It is good practice to clean your detector after each use. Only fresh water should be used when cleaning. Never use abrasives or solvents to clean the detector. The detection coil is waterproof and can be washed with the hose. The Screen pod should only be carefully wiped with a clean damp cloth to avoid any water or moisture ingress.
No. It is not necessary to lubricate or grease any part of the detector. Using any petroleum-based grease can damage the plastics and void the warranty.
To disable the audio tones, you simply need to push and hold the "minus" button when powering the PRO-FIND 40 on.
To enable the audio tones, you simply need to push and hold the "plus" button when powering the PRO-FIND 40 on.
To disable the ferrous tones OFF simply push and hold the "minus" button when the PRO-FIND 40 is powered on and then wait for the long beep.
To enable the ferrous tones ON simply push and hold the "plus" button when the PRO-FIND 40 is powered on and then wait for the long beep.
No, the LED flashlight cannot be adjusted.
No, the vibration cannot be toggled ON/OFF.
The Rapid Re-tune feature was designed so that users do not have to power cycle the pin-pointers to re-tune the PRO-FIND to the environment.
To re-tune the PRO-FIND 40 simply short-press the power button when the PRO-FIND 40 is powered on.
At maximum Sensitivity the PRO-FIND 40 can detect targets at greater distances which can be both an advantage and a disadvantage. To pinpoint a target sometimes it’s better to have a less sensitive probe to reduce the search area, so we have given you the ability to adjust it how you see fit. The Sensitivity may also need to be reduced in mineralised or salty soils, so that you are only detecting metal and not the minerals in the ground.
Side detection occurring with the target (or multiple) in the side of the hole. Use the tip of the probe to check around the sides of the hole. Reducing the Sensitivity can also help.
Yes, but be aware that the PRO-FIND 40 won’t have the same sensitivity to very small nuggets as a quality Minelab metal detector. It will be a good aid in target recovery for larger nuggets.
Yes, the PRO-FIND 40 is waterproof to 3 meters (10ft) and can be washed. When washing always use clean fresh water.
If no targets are detected or buttons pressed for 5 minutes, then the PRO-FIND 40 will start a slow constant beep (Lost Alarm) this alarm will sound for 5 minutes and then the PRO-FIND 40 will power off to save battery life.
The battery may be flat or inserted incorrectly. Replace the battery and/or check the battery orientation. If you are still having issues, contact your closest Minelab Service Centre.
The PRO-FIND 40 has a 3rd beep that notifies you that the pin-pointer has calibrated to the environment. This can sometimes take up to 30 seconds to occur depending on environmental conditions. You can short press the power button to perform a rapid re-tune. You should then hear a confirmation beep and the PRO-FIND 40 should now detect metals.
Tips for switching on:
*Calibration usually takes less than a second when the unit has been used recently.*
In highly mineralised soils:
Birkaç dakika boyunca hiçbir hedef tespit edilmezse veya tuşa basılmazsa, cihaz kayıp alarmı başlatır, bu uzun bir bip sesi çıkarır, böylece pin işaretçinizi bulabilirsiniz. Birkaç dakika sonra, pim göstergesi pil ömrünü korumak için kendiliğinden kapanacaktır.
Bu, bir çukur kazdıktan sonra zeminde geride kalırsa üniteyi bulmanızı sağlar. Bip sadece titreşim modunda ise meydana gelmez. 5 dakikalık yavaş bip sesinin ardından cihaz kendi kendine kapanır.
Kapak devam ederse, pil yanlış yerleştirilmiş olabilir, ancak sıkılması zor olabilir. Anahtarlı plastik, pil sekmelerinin temas noktalarına temas etmesini önler - bunu düzeltmek için pilleri ters çevirin.
Pro-Find'ı açtıktan sonra 2 bip sesi ve ardından kısa bir üçüncü kalibrasyon bip sesi duyacaksınız. Bu kalibrasyon bazen 15-20 saniye sürebilir, lütfen Pro-Find'ı herhangi bir metalik nesnenin yakınına yerleştirmeden önce bu kalibrasyon bipinin oluşmasını bekleyin. Eğer metal değiştirdiğinizde Pro-Find'a sahipseniz, kalibre edilmez ve Pro-Find'ı yeniden başlatmanız gerekir.
Deliğin yanındaki hedefte (veya çoklu) meydana gelen yan algılama. Deliğin kenarlarını kontrol etmek için sondanın ucunu kullanın. Hassasiyeti azaltmak da yardımcı olabilir.
Evet, ancak kaliteli bir Minelab Altın Dedektörü ile çok küçük külçelere karşı aynı duyarlılığa sahip olmayacağının farkında olun. Daha büyük külçeler için hedef toparlanmasında iyi bir yardımcı olacaktır.
Maksimum Hassasiyette PRO-FIND 35, hem avantaj hem de dezavantaj olabilen daha uzak mesafedeki hedefleri tespit edebilir. Bir hedefi kesin olarak belirlemek için, arama alanını azaltmak için daha az hassas bir sondaya sahip olmak daha iyidir, bu yüzden size uygun gördüğünüz şekilde ayarlama imkanı verdik. Hassasiyetin mineralli veya tuzlu topraklarda da azaltılması gerekebilir, böylece yalnızca metali tespit edersiniz, zemini değil.
PRO-FIND 35 tamamen 3 metreye kadar su geçirmezdir, böylece temizlemek için iğne işaretçisini suya batırabilirsiniz. Pin işaretçisini batırmadan önce pil kapağının tamamen sıkıldığından emin olun.
PRO-FIND 15 sadece suya dayanıklıdır. Hoparlör havalandırmasını baş parmağınızla kapatırsanız, akan su altında yıkayabilirsiniz.
Açmak için ipuçları:
Birim son zamanlarda kullanıldığında kalibrasyon genellikle bir saniyeden daha kısa sürer
Çok mineralli topraklarda:
Ses açma ve kapatma (yalnızca Pro-Find 35):
Demir tonu açma ve kapatma (yalnızca Pro-Find 35):
CTX 3030, GPZ 7000 ve XChange 2, veri depolaması için SQLite kullanır. SQLiteSpy gibi bir araç kullanmak, dosyaların çıkarılmasına yardımcı olabilir. Ayıklanan dosya doğrudan çalıştığı için SQLiteSpy'ı kurmanıza gerek yoktur.
1. Dedektörü bir PC'ye takın ve oluşturulan yeni çıkarılabilir sürücüye gidin.
2. Sürücüyü açın.
3. İçinde bir dosya bulacaksınız. Bunu kullanmak için bir konuma kopyalayın. Bu dosya, açılması gereken depolama veritabanıdır.
1. XChange 2'de çıkarmak istediğiniz noktaları seçin.
2. Bunları "Dosya" klasörüne sürükleyin.
3. 'dosya' klasörünü tıklayarak açın.
4. 'Bir Minelab dosyasını dışa aktar' düğmesine tıklayın.
5. Dosya, 'İndirilenler' klasörünüzde olmalıdır.
6. İndirilen bu dosya sıkıştırılmıştır, bu nedenle içindeki 'shareData' dosyasını çıkarmak için 7zip gibi bir araç kullanmanız gerekecektir.
7. 'ShareData'yı kullanmak için bir konuma kopyalayın. Bu dosya, açılması gereken depolama veritabanındadır.
Bu örnekte SQLiteSpy kullanılmıştır ancak benzer bir işlem diğer araçlar için geçerlidir.
1. SQLiteSpy'ı açın
2. "Dosya"> "Veritabanını Aç ..." ı seçin.
3. Veritabanının konumuna gidin.
4. Dosya türünü 'Herhangi bir dosya (*. *)' Olarak değiştirin
5. Veritabanını seçin ve 'Aç'ı seçin
6. Solda, kullanılan veritabanı dosyasına bağlı olarak birkaç tablo vardır.
a. "bulma noktası": bu, kaydedilen her bir FindPoint'i içerir
b. "ara nokta": Bu, kaydedilen her bir WayPoint'i içerir
c. "nokta": Bu, tüm GeoHunt'larda bir iz oluşturmak için kullanılan noktaların her birini içerir. Her GeoHunt'ın "geohunt_fk" sütununda bir UUID ile tanımlandığını unutmayın.
d. "geohunt": Bu, GeoHunt'ların her birini tanımlamak için "puan" tablosunda kullanılan UUID'yi içerir.
7. Ayrıca bazı FindPoint'leri çıkarmak istediğinizi varsayalım (aynı prosedür diğer noktalar için de kullanılır).
8. "Bulma noktası" tablosuna çift tıklayın. Bu, çıkarılan tüm FindPoint'leri gösterecektir.
9. Tablodaki bir satıra tıklayın ve ardından tüm satırları seçmek için “Ctrl + A” tuşuna basın.
10. Tüm verileri kopyalamak için “Ctrl + C” tuşuna basın.
11. Excel'i açın
12. Verileri elektronik tabloya yapıştırın.
13. Bazı veritabanı dosyalarında enlem ve boylamın, kullanım için doğru biçime sokulması için 10.000.000'e bölünmesi gerekir.
14. Buradaki puanlarla ne gerekiyorsa yap.
